top of page
Indepependent Tree Service
Call Us: 406-212-1963
"More than just a tree service!"
Firewood IS still available
Call or Text 406-212-1963
Open by Appointment
Available Equipment
2817 US HWY 2 West Kalispell MT 59901
1985 F800 4x4 Chip Truck
370-4V Gas Motor
5-speed
Hi-Lo Range 4x4
Lock Out Hubs
New Battery
New Ring Gear
Newer Edelbrock Carb
Block Heater
Good matching & siped tires
Forestry DUMPING chip box
Crane in bed for lifting rounds
Tons of external tool storage
Warn Winch
Tire Chains
Pintle Hitch
Dual Fuel Tanks
Rear roller fairlead for integrated winch
Many dry tool boxes for storage & ramps
1'' thick steel plate with D-rings for equipment storage behind cab: stump grinder, skidsteer, ATV, Snowmobile, fuel transfer tank etc
This is a massively built F800 4x4 chip/dump truck that would be a great asset to any tree service or firewood cutter.
Will need minor finishing touches and brakes bled, but runs well, drives, starts & stops as it is now. We have been using it for winter chipping jobs, storm damage work and around our firewood yard.
$15,500.
"The Crusher" is an incredible machinist built log splitter.
Powered by a 4cyl gas engine, this machine will handle just about anything you feed it.
Two spool valve would allow the addition of a log lift if desired.
Capable of splitting a 36" log and it even has a crane to help lift if needed!
Wisconsin VH4D Engine
4 cylinder
30HP
Gasoline
Electric Start
New Battery
Work Lights
Full 36" stroke has a 17 second cycle time.
Common 16" stroke has only an 8 second cycle time.
2 5/16 hitch
6 round pin connector
Axle has brakes (not connected)
Fresh paint
Ready for work.
$4,200.
Back and time saving Firewood Conveyor
25ft length
Elevator- Adjustable Height can easily load the tallest dump truck.
5hp gasoline Briggs & Stratton engine
1 7/8 hitch
$1,400.
Thermo Lay Hot Asphalt and Sanding Box.
This box hydraulically mixes / dispenses asphalt and keeps mix hot via thermostatic on board propane or AC electric.
This unit can also double as a road sander with an added spinner at the rear.
Has hydraulic lift plate compactor tray, diesel spray wand, remote hydraulic tool connection, a small water tank, another spray wand and remote torch.
Google search Thermo Lay UD-425-120 for a pdf of features and specs.
Can possibly deliver.
Asphalt Patch Box only. Truck is Not for sale.
$6,500.
Western 8' plow, frame, Wiring Harness and Aftermarket bumper
Fits 1972-1992 Dodge Half thru One Ton Trucks (W100-300 & D150-D350)
Assembly includes everything you need to get plowing snow and includes the incorporated aftermarket front bumper thats made out of Diamond plate. Bumper has auxiliary lights and two 2" Receivers for a trailer hitch, carrying a winch and/or recovery operations.
This is a great set up and can also take a Meyers plow as well.
Truck is NOT available.
$4,500.
Considering selling components gathered to build a processor.
This would include:
1) Specialty piece of equipment with enclosed cab and overhead crane to serve as powerplant and operators cab (with A/C).
Powered by John Deere diesel, with huge valve block and numerous foot/wheel/joystick controls.
(GPM unknown at this time)
This unit is designed and capable of driving on a hard surface like concrete, or stationed on a trailer as we have it.
2) Giant bearing press table to be used as a splitting platform. This is currently plumbed to power unit and can demonstrate stroke & operation. No splitting wedges or push plates have yet been made or fitted, but the build is overkill and mounting a hydraulic saw would be easy.
3) Gooseneck tandem trailer Not included
4) 30ft (?) Conveyor (not shown), which was a hay conveyor/elevator with dual chain drive paddles, hand crank elevation adjustment, and powered by a gasoline engine. We were going to add a hydraulic motor to power this but have been using it independently for our firewood yard.
$10,000. for all of it. Will not separate.
bottom of page